Garage remote not working from outside. A garage remote is a suitable and practical device that allows you to open and close your garage door without having to actually touch the door or use a key.
Nevertheless, if your garage remote is not working from outside, it can be a major hassle and can even leave you stuck outside of your own home.
Garage remote not working from outside
The following are the reasons due to which your garage remote is not working from outside.
Batteries are dead
There are more than a few reasons why your garage remote may not be operational from outside.
One of the most common reasons is that the remote’s batteries may be low or dead.
This is an easy problem to fix, as you can simply replace the batteries in the remote. However, if you’ve replaced the batteries and the remote is still not working, you may have a more serious problem.
Solution to this problem
To replace the batteries in a garage door remote, you will need to locate the battery compartment, which is typically located on the back or underside of the remote.
Once you have found the battery compartment, remove the old batteries, and substitute them with new ones, making sure to match up the positive and negative sides of the batteries to the markings in the compartment.
After replacing the batteries, test the remote to ensure that it is working well.
Remote signals are weak
A further reason that your garage remote may not be working from outside is that the remote’s signal may be weak.
This can happen if the remote is too far away from the garage door opener or if there are obstacles in the way that are blocking the signal.
Solution to this problem
Make sure the batteries in the remote are fresh and properly installed. Weak batteries can trigger the remote to send weak signals.
Dust, dirt, and other debris can accumulate on the remote’s buttons and antenna, which can weaken the signal. Clean the remote with a dry cloth or compressed air.
The signal from the remote may be fainter if you are too far away from the receiver. Try moving closer to the receiver when using the remote.
Other electronic devices or appliances can cause intrusion that can weaken the signal from the remote. Attempt using the remote in a different location or at a different time to see if the signal strength improves.
If the antenna of the receiver is damaged or not functioning, it can affect the signal intensity. You may need to replace the antenna or contact the manufacturer for help. If none of the above explanations work, it may be necessary to replace the remote.
Circuit board is damaged
Last of all, if all the above problems have been checked and yet the remote is still not working, the problem may lie in the circuit board of the opener.
The circuit board controls the opener’s functions and if it has malfunctioned, the opener will not work. The circuit board will have to be replaced in this case
Solution to this problem
Before you begin, make sure the opener is unplugged to avoid any electrical hazards. The circuit board is normally situated in the bounds of the opener’s motor unit.
It may be necessary to remove the cover of the unit to access the board. Thoroughly examine the circuit board for signs of damage such as burn marks, cracked components, or loose connections.
Remote’s code is changed
Another reason that your garage remote may not be working from outside is that the remote’s code may have been changed.
This can happen if someone else has accidentally pressed the “learn” button on the garage door opener, which erases the current code and allows a new one to be programmed.
Solution to this problem
To resolve this issue, you will need to reprogram your remote with the new code in order to make it work again.
Antenna is damaged
Another possible reason that your garage remote may not be working from outside is that the garage door openers antenna may be damaged or obstructed.
The antenna is responsible for receiving the signal from the remote and if it is damaged or obstructed, it will not be able to receive the signal.
Solution to this problem
The antenna of the receiver is typically located near the top of the opener’s motor unit. Before you begin, make sure the opener is unplugged to avoid any electrical hazards.
Once you have located the antenna, use a screwdriver to remove the screws that hold it in place. Carefully remove the old antenna from the opener.
Take the new antenna and attach it to the opener by turning it into place. Make sure the antenna is securely fastened.
After replacing the antenna, plug the opener back in and test the remote to see if the signal strength has improved.
Conclusion
In conclusion, a garage remote not working from outside can be a major inconvenience. However, it is usually a simple problem that can be fixed with a little troubleshooting. By checking the batteries, signal strength, code, antenna, and circuit board, you should be able to determine the cause of the problem and fix it quickly. Remember to regularly check the batteries, antenna, and circuit board, and troubleshoot the remote in case of any issues.